How-to

How to Use a Polariscope: Testing Gemstones Step by Step

How a polariscope works, the four reactions it shows, a step-by-step testing method, reading optic figures with a conoscope sphere, and which model suits your bench.

Faceted green quartz gemstones on a white surface
In this guide

    Quick answer: To use a polariscope, cross the two filters until the field goes dark, place the stone on the lower filter and rotate it through a full turn. A stone that stays dark is singly refractive (diamond, spinel, garnet, glass). A stone that blinks light and dark four times is doubly refractive (sapphire, ruby, quartz, tourmaline, topaz). A stone that stays light is an aggregate (chalcedony, jade). Always test in three directions, and confirm the result with a refractometer.

    The polariscope is one of the fastest and least expensive instruments on a gemmologist's bench. In about ten seconds, with no contact liquid and no risk to the stone, it tells you how a gem handles light, and that single fact separates ruby from red spinel, sapphire from blue glass, and jade from most of its imitations. This guide covers how the instrument works, the four reactions you will see, a step-by-step testing method, how to read an optic figure, and what the polariscope cannot tell you.

    What is a polariscope and how does it work?

    A polariscope is two polarising filters with a light source underneath. The lower filter is the polariser and the upper one, which you look through, is the analyser. Each filter only lets through light vibrating in one direction. When the two are turned at right angles to each other, the crossed position, no light gets through and the view between them goes dark.

    A gemstone placed between the crossed filters either leaves that darkness alone or changes it. Singly refractive stones pass light without altering it, so the field stays dark. Doubly refractive stones split light into two rays vibrating in different directions, which lets some light through the analyser in certain positions. Watching what happens as you rotate the stone tells you which kind of material you are holding.

    What does a polariscope tell you? The four reactions

    Reaction as you rotate the stone What it means Typical stones
    Stays dark through the whole turn Singly refractive (SR) Diamond, spinel, garnet, glass, cubic zirconia
    Blinks light and dark four times in a full turn Doubly refractive (DR) Sapphire, ruby, quartz, tourmaline, topaz, beryl, peridot, zircon
    Stays light through the whole turn Aggregate (AGG), made of many tiny crystals Chalcedony, agate, jadeite, nephrite
    Shifting dark bands, patches or a cross-hatched pattern Anomalous double refraction (ADR), strain in a singly refractive stone Garnet, synthetic spinel, glass, amber

    How to use a polariscope: step by step

    1. Clean the stone. Dust and grease scatter light and blur the reaction. Wipe the stone with a lint-free cloth.
    2. Cross the filters. Switch on the light and turn the analyser until the field between the filters is at its darkest.
    3. Place the stone on the lower filter. Start with the table facet down. Stone tweezers or a small glass dish make small stones easier to handle.
    4. Rotate the stone through a full turn. Turn the stone, not the filters, and watch it through the analyser for the whole 360 degrees.
    5. Read the reaction. Dark throughout is singly refractive, four blinks is doubly refractive, light throughout is an aggregate. Use the table above.
    6. Repeat in two more directions. Turn the stone onto its side and then onto another facet and test again. A doubly refractive stone looks singly refractive when you happen to look straight down its optic axis, so one direction is never enough.
    7. Confirm with a second instrument. Record the result, then check refractive index on a refractometer. Our refractometer guide walks through that test.

    How do you tell ADR from true double refraction?

    Strain inside a singly refractive stone can let patches of light through the crossed filters, and a beginner can mistake that for the blink of a doubly refractive stone. Synthetic spinel is the classic example, with its cross-hatched pattern, and garnet and glass do it too. The pattern is the first clue: true double refraction gives a clean change from light to dark every quarter turn, while ADR gives irregular bands that crawl across the stone.

    When you are unsure, use the confirmation test. Turn the stone to the position where it looks lightest, then rotate the analyser a quarter turn so the filters are no longer crossed. If the stone becomes noticeably brighter, it is singly refractive with ADR. If it stays about the same or goes darker, it is doubly refractive.

    Finding the optic figure with a conoscope sphere

    Once you know a stone is doubly refractive, the polariscope can take you one step further and tell you whether it is uniaxial or biaxial. For this you need a conoscope, a small strain-free glass sphere sold as a sphere for polariscope.

    With the filters crossed, turn the stone until you see bands of interference colour, which appear when you are looking close to an optic axis. Hold the sphere just above that spot and an interference figure appears in it.

    • Uniaxial figure: a dark cross surrounded by coloured rings. Sapphire, ruby, tourmaline, beryl and zircon are uniaxial. Quartz shows a distinctive version with a hollow centre, the bull's-eye figure, which is a quick way to recognise amethyst and citrine.
    • Biaxial figure: one or two curved dark brushes that swing as the stone is turned, without the fixed cross. Topaz, peridot, chrysoberyl and tanzanite are biaxial.

    Finding a figure takes practice, especially on small or heavily faceted stones. Start with a large piece of quartz, where the bull's-eye is easy to find, before moving on to harder cases.

    What a polariscope cannot do

    • It does not work on opaque stones. Light has to pass through the gem, so the test is limited to transparent and translucent material.
    • It can be misled by assembled stones. Doublets and triplets combine different materials and give confusing reactions.
    • It does not separate natural from synthetic. A synthetic sapphire is doubly refractive, exactly like a natural one.
    • It does not identify a stone by itself. Diamond and cubic zirconia are both singly refractive, so a polariscope cannot tell them apart. That is a job for a diamond tester.
    • Heavily included or fractured stones can mislead. A badly fractured doubly refractive stone may stay light like an aggregate.

    Treat the polariscope as the first test in a sequence. Follow it with a refractometer for refractive index, a dichroscope for pleochroism, a Chelsea filter for a quick colour check and a 10x loupe for inclusions.

    Which polariscope should you buy?

    The right model depends on where you work. Prices are in Thai Baht at the time of writing.

    Model Price Best for
    Gemax Folding Polari-Loupe 950 THB A pocket check at gem markets and buying trips
    Gemax Polariscope Handy 1,450 THB Travel and field work; built-in yellow LED, runs on two CR2032 batteries
    Polariscope White LED, Large 2,895 THB Bench, lab and classroom use with white light
    Polariscope Yellow LED, Large 2,895 THB Bench, lab and classroom use with yellow light
    Gemax Polariscope Dual Light 3,875 THB Working gemmologists who want both yellow and white light in one unit

    White light is the general-purpose choice and shows interference figures in colour. Yellow light gives a higher-contrast view that many gemmologists prefer for reading reactions. If you test stones every day, the dual-light model saves you choosing. Add the conoscope sphere to any bench model if you want to read optic figures, and consider a complete gemological kit if you are equipping a bench from scratch.

    The bottom line

    A polariscope will not name a gemstone, but it narrows the field faster than any other instrument for the money. Cross the filters, rotate the stone, test in three directions and write down what you see. Then let the refractometer and the loupe finish the job. Browse our full range of gem identification tools, or ask our team which setup suits your work. Genuine stock, shipped worldwide from Bangkok since 2001.

    Frequently asked questions

    What does a polariscope do in gemology?

    A polariscope shows how a gemstone handles polarised light. In about ten seconds it tells you whether a transparent or translucent stone is singly refractive, doubly refractive or an aggregate, which separates stones such as ruby (doubly refractive) from red spinel and garnet (singly refractive).

    How do you use a polariscope?

    Cross the two filters until the field is dark, place the clean stone on the lower filter and rotate it through a full turn while watching through the top filter. Dark throughout means singly refractive, four blinks means doubly refractive, and light throughout means an aggregate. Repeat in three directions.

    Why does my gemstone stay dark in the polariscope?

    Either it is singly refractive, like diamond, spinel, garnet or glass, or it is a doubly refractive stone that you are viewing straight down its optic axis. That is why every stone should be tested in at least three different directions before you record a result.

    What is anomalous double refraction (ADR)?

    ADR is a false double refraction effect caused by internal strain in a singly refractive stone. It shows as irregular dark bands or a cross-hatched pattern, typically in synthetic spinel, garnet and glass. To confirm it, turn the stone to its lightest position and rotate the analyser a quarter turn: if the stone gets noticeably brighter, it is singly refractive with ADR.

    Can a polariscope tell a natural gemstone from a synthetic one?

    No. A synthetic sapphire is doubly refractive exactly like a natural one, and diamond and cubic zirconia are both singly refractive. The polariscope narrows down what a stone can be; a refractometer, loupe and other instruments are needed to finish the identification.

    How much does a polariscope cost?

    At the time of writing, Sachi polariscopes range from 950 THB for a folding pocket polari-loupe and 1,450 THB for the battery-powered Gemax Handy, to 2,895 THB for large bench models and 3,875 THB for the Gemax Dual Light with both yellow and white light.

    Written by Kunal Jain

    Sachi Gems & Tools Co. Ltd., Bangkok. The Sachi buying guides distill what our team has learned supplying gemological instruments and jewellery tools to gem labs, jewellers and sorting houses worldwide since 2001. Questions about anything in this guide? Ask our Bangkok team.