Quick answer: Diamond polishing powder is graded by particle size in microns, and the smaller the number, the finer the finish. For a final polish on sapphire, ruby, spinel and other hard stones, use 0-0.5 or 0-0.25 micron, working up to it through coarser grades such as 0-3 and 0-1. Softer stones such as quartz, beryl and opal polish faster and more cheaply on cerium oxide or tin oxide. A single 10 carat bottle of diamond powder charges a lap many times.
Every faceted gemstone and polished cabochon gets its shine the same way: a sequence of progressively finer abrasives, each one removing the scratches left by the one before. Diamond powder is the abrasive that makes this possible on the hardest stones, and the one professional cutters reach for when nothing else will bite. This guide explains how diamond powders are graded, which grade does which job, when a cheaper oxide polish is the better choice, and how to charge a lap properly. It is written from the questions cutters ask across our counter in Bangkok every week.
What is diamond polishing powder?
Diamond polishing powder is synthetic diamond crushed and graded into extremely fine, tightly controlled particle sizes. Diamond is the hardest material used in lapidary work, so it cuts and polishes every gemstone, including the ones that defeat ordinary abrasives: sapphire, ruby, chrysoberyl, spinel, topaz and cubic zirconia. Synthetic diamond is the trade standard for this work because it can be graded far more consistently than natural diamond dust, and consistency is what matters. One oversized particle in a fine powder leaves a scratch that sends you back a step.
You will also see it sold as diamond abrasive powder, diamond lapping powder or diamond micron powder. These are the same product family; the names simply describe the job (lapping and polishing) or the grading method (microns).
Micron vs mesh: how are diamond powders graded?
Two grading systems are in use, and they run in opposite directions.
- Mesh describes a sieve: the number of openings per inch. A higher mesh number means a finer powder. Mesh grading is used for coarser powders, where particles are large enough to sieve.
- Micron describes the particle itself: one micron is a thousandth of a millimetre. A lower micron number means a finer powder. Micron grading takes over for the fine and ultra-fine powders used in polishing, which are far too small to sieve.
Micron powders are usually sold as a range. A grade marked 0-2 contains particles from near zero up to 2 microns, and it is the upper figure that governs the finish, because the largest particles leave the deepest scratches. As a rough guide for comparing the two systems, mesh #170-200 is about 75 to 90 microns, #200-230 is about 63 to 75 microns and #230-270 is about 53 to 63 microns. All three are far coarser than any polishing grade.
Which micron grade should you use?
Our Sachi Diamond Polishing Powder comes in twelve grades from 0-0.25 to 0-10 micron, and the Sachi Pre Polish Diamond Powder covers the coarser mesh sizes used before polishing begins. The table shows where each one sits in the sequence. Grit equivalents are approximate and vary between manufacturers, so treat them as a comparison aid, not a specification.
| Grade | Approximate grit equivalent | Typical job |
|---|---|---|
| Mesh #170-200, #200-230, #230-270 | 53 to 90 microns | Surface preparation, coarse lapping and charging cutting discs |
| 0-10, 0-9, 0-8, 0-7 micron | Around 1,800 to 2,000 grit | Fine smoothing after cutting, removing lap marks |
| 0-6, 0-5, 0-4 micron | Around 3,000 grit | Pre-polish on hard stones |
| 0-3, 0-2 micron | Around 8,000 grit | Fine pre-polish; the last step before the final polish |
| 0-1 micron | Around 14,000 grit | Final polish on many stones; last pre-polish for the hardest |
| 0-0.5 micron | Around 50,000 to 60,000 grit | Standard final polish for sapphire, ruby, spinel and cubic zirconia |
| 0-0.25 micron | Around 100,000 grit | Mirror finish for competition cutting and the finest work |
You do not need all twelve grades. A practical sequence for hard stones is three steps: a pre-polish around 0-3, a fine step at 0-1, and a final polish at 0-0.5. Add 0-0.25 if you want the last degree of brilliance, and a coarser grade such as 0-6 if your cutting laps leave deep marks. The rule that matters is not to jump too far in one step. Each grade should only have to remove the scratches of the grade before it.
Diamond, cerium, tin or aluminium oxide: which powder for which stone?
Diamond will polish anything, but it is not always the best or cheapest choice. Softer stones often take a better finish, faster, from an oxide polish, and oxide powders cost far less per gram. The deciding factor is the hardness of the stone.
| Polishing powder | Best suited to | Notes |
|---|---|---|
| Diamond powder | Sapphire, ruby, chrysoberyl, spinel, topaz, cubic zirconia and any stone of hardness 8 or above | The only practical polish for corundum. Mixed with a light oil. |
| Cerium oxide | Quartz (amethyst, citrine, agate), beryl (emerald, aquamarine), opal and glass | The classic quartz polish. Mixed with water to a thin slurry. |
| Tin oxide | Softer gemstones and cabochons, and decorative stone such as marble and granite | A gentle, forgiving general polish. Mixed with water. |
| Aluminium oxide | Lapping and smoothing; commonly used on mid-hardness stones such as garnet, tourmaline and peridot | A versatile workshop staple between the oxides and diamond. |
Many cutters keep both: diamond for the hard stones and for pre-polish steps, and an oxide for the final polish on quartz and beryl. The full range is in our diamond polishing powder and other polishing media collections.
How to charge a lap and polish with diamond powder
- Choose a lap that suits the grade. Harder metal laps hold coarser diamond for pre-polish work; softer metal and composite laps are used for the fine and final grades. See our grinding and polishing laps and composite polishing laps.
- Mix a small amount with a carrier. Put a pinch of diamond powder in a clean dish and add a few drops of light oil until it forms a thin paste. Oxide powders are mixed with water instead.
- Apply sparingly. Dab the paste onto the stationary lap and spread it into a thin, even film with a clean fingertip. More powder does not polish faster; it only wastes diamond and can cause scratching.
- Polish with light pressure. Run the lap at a slow to moderate speed and sweep the stone across it. Let the diamond do the work, and keep the stone cool.
- Inspect often. Wipe the facet and check it under a 10x loupe. Move on only when every scratch from the previous grade is gone.
- Clean everything before the next grade. Wash the stone, the dop, your hands and the splash pan. A single stray grain of a coarser grade will scratch a finished facet.
- Keep one lap per grade. Label each lap with its micron size and store it in its own bag so grades never mix.
Common mistakes that ruin a polish
- Overcharging the lap. A thick layer of powder rolls between stone and lap and scratches. A thin film cuts cleanly.
- Skipping grades. Jumping from a coarse pre-polish straight to 0-0.5 micron leaves deep scratches that the fine powder cannot remove in any reasonable time.
- Cross-contamination. Most mystery scratches come from a coarser grade carried over on a cloth, a fingertip or a shared lap.
- Too much pressure or speed. Heat can damage sensitive stones and lift the stone from the dop. Light and slow gives a flatter, brighter facet.
- The wrong powder for the stone. Oxide polishes will not touch sapphire or ruby, and diamond can be needlessly aggressive on soft stones.
How much does diamond powder cost, and how much do you need?
Less than most people expect. At the time of writing, Sachi Diamond Polishing Powder is 100 THB per 10 carat bottle in every grade from 0-0.25 to 0-10 micron, and the pre-polish mesh grades are 165 THB per bottle. Ten carats is 2 grams. That sounds small, but a charge uses only a pinch, so one bottle of each grade in your sequence lasts a hobby cutter a long time and a working cutter through many stones. Tin oxide and aluminium oxide come in 500 gram packs, and cerium oxide in a 1 kilogram pack. Custom mesh sizes can also be supplied on request.
Lapidary clubs, cutting workshops and resellers ordering in quantity can ask us for a trade quote. We ship worldwide from Bangkok; see our delivery guides for Australia and the USA.
The bottom line
Match the powder to the stone, step down through the grades without skipping, use far less powder than feels natural, and keep every grade strictly separate. Do that and a few inexpensive bottles will take a stone from a sawn surface to a mirror polish. If you are still setting up, our lapidary machine buyer's guide covers the machines and laps, and the complete lapidary machines and supplies collection has everything from saw blades to final polish. Genuine stock, shipped worldwide from Bangkok since 2001.


